Menu Close
Pipeliner Family

Diameters / Packaging

Diameters
 (4) 14 lb Coil
0.068 in (1.7 mm) ED036650
2.0 mm (5/64 in) ED031968

Pipeliner® NR®-208-XP

Flux-Cored Self-Shielded (FCAW-S)

CLASSIFICATIONS:
E81T8-G
E81T8-A4-K12

Pipeliner® NR®-208-XP from Lincoln Electric has been micro-alloyed to be capable of exceeding impact values of 68 J (50 ft·lbf) @ -29°C (-20°F).

Diameter

Select Diameter

  • 0.068 in (1.7 mm)
  • 2.0 mm (5/64 in)

Package

Select Package

  • (4) 14 lb Coil
Buy Now

DETAILS

Has been micro-alloyed to be capable of exceeding impact values of 68 J (50 ft·lbf) @ -29°C (-20°F). It is recommended for hot, fill and cap pass welding of up to X80 grade pipe.

Features

  • Vertical down hot, fill and cap pass welding of up to X80 grade pipe
  • Capable of producing weld deposits with impact toughnesss exceeding 122 J (90 ft·lbf) at -40°C (-40°F)
  • ProTech® hermetically sealed packaging

Typical Applications

  • Hot, fill and cap pass welding of up to X80 grade pipe
  • Cold temperature cross country pipe applications

Welding Positions

  • All except vertical up

Shielding Gas

  • N/A

Disclaimers

Warning -

Cancer and Reproductive Harm -

www.P65Warnings.ca.gov

Service Information

Documentation

You May Also Need

K126 Classic 350A FCAW-SS

K126® Classic® Innershield® 350A FCAW-SS Welding Gun 15 ft 062-332

K126-2
14lb Coil Innershield NR-207 Hermetically Sealed Pail

Innershield® NR®-207

ED012438
50 lb Can of Lincoln Electric Stick Electrodes

Pipeliner® 8P+

ED030826
Pipeliner

Pipeliner® NR®-207+

ED030924
View All

BEFORE USE, READ AND UNDERSTAND THE SAFETY DATA SHEET (SDS) FOR THIS PRODUCT AND SPECIFIC INFORMATION PRINTED ON THE PRODUCT CONTAINER. SDS Search page

See test result disclaimer

CONFORMANCE

CONFORMANCES SPECIFICATION CLASSIFICATION
AWS AWS A5.29 E81T8-G
AWS AWS A5.36 E81T8-A4-K12

MECHANICAL PROPERTIES

Classification Polarity Yield Strength @ 0.2% Offset
MPa (ksi) 		Tensile Strength
MPa (ksi) 		Elongation
% 		Charpy V-Notch
J (ft-lbs) @ -30°C (-20°F) 		Charpy V-Notch
J (ft-lbs) @ -40°C (-40°F) 		Hardness Rockwell B
E81T8-G Requirement DC- 470 (68) min. 550-690 (80-100) 19 min. Info. Only
E81T8-A4-K12 Requirement DC- 470 (68) min. 550-690 (80-100) 19 min. 27 (20) min. Info. Only
Typical Result, As-welded DC- 490-560 (70-81) 550-630 (80-91) 20-29 52-301 (38-222) 94-167 (69-123) 92
Typical Result, As-welded DC+ 520-540 (76-78) 590-610 (86-88) 20-26 94-235 (69-174)

DEPOSIT COMPOSITION

Classification Polarity %Al %B %C %Cr %Cu %Mn %Mo %Ni %P %S %Si %V
E81T8-G Requirement DC- 1.8 max. Info. Only 0.30 min. * 0.50 min. * 0.20 min. * 0.50 min. * 0.030 max. 0.030 max. 1.00 max. 0.10 min. *
E81T8-A4-K12 Requirement DC- 1.8 max. 0.15 max. 0.20 max. 1.50 - 2.75 0.50 max. 0.75 - 2.00 0.030 max. 0.030 max. 0.80 max. 0.05 max.
Typical Result DC- 0.7-1.2 0.0014 max. 0.01-0.03 0.04-0.07 0.04-0.07 2.21-2.56 0.02 max. 1.04-1.22 0.006-0.015 0.003 max. 0.12-0.15 0.003 max.
Typical Result DC+ 1.0-1.2 0.001 max. 0.01-0.02 0.05-0.06 2.27-2.46 0.01-0.02 1.12-1.15 0.008-0.010 0.003 max. 0.12-0.14 0.003 max.

TYPICAL OPERATING PROCEDURES

Diameter Polarity CTWD
mm (in.)⁽¹⁾ 		Wire Feed Speed
m/min (in/min) 		Voltage
volts 		Approx. Current
amps 		Melt-off Rate
kg/hr (lb/hr) 		Deposition Rate
kg/hr (lb/hr) 		Efficiency
%
1.7mm (0.068 in) DC- 19 (3/4) 1.7-3.8 (70-150) 16-22 165-250 1.4-3.1 (3.1-6.8) 1.1-2.5 (2.5-5.5) 78-81
2.0 mm (5/64 in) DC- 19 (3/4) 1.7-3.3 (70-130) 17-20 195-295 1.8-3.5 (4.0-7.6) 1.5-2.9 (3.3-6.4) 82-83

NOTES

Note
* To meet the requirements of a "G" classification, the chemical composition of the weld deposit must meet the minimum requirement for one or more of these elements.
⁽¹⁾ For electrical stickout (ESO) subtract 6.4 mm (1/4 in) from contact tip to work distance (CTWD).